과정소개 |
한국휴렛팩커드 교육센터는 2024 EPI Silver Partner입니다. [과정소개] - 해당과정은 CDCP자격증을 소지한 자만 교육에 참여할 수 있습니다. 즉 CDCP자격증이 없는 사람은 과정에 참여할수 없습니다.
- CDCP 자격증 취득자가 유효기간 만료 후 6개월 이내면, 상위버전인 CDCS 과정 수강 및 자격증 취득 가능합니다
- Data Center의 목적에 맞는 밴더 장비를 선택하고 그에 맞게 설계, 구성 및 검증하며 가장 효율적으로 관리할 수 있는 방법들을 제공합니다.
- 데이터센터의 디자인 라이프 사이클을 이해하고, 고객의 요구사항을 충족시키기 위해 벤더와 공급자 간따른 디테일한 요구사항을 확인하여 벤더로부터 제안된 기술적인 디자인 플랜, 견적, 제안을 검증할수 있습니다.
- Maintenance Tier-level과 데이터센터 디자인을 위한 Tier-level을 이해하고 소방대책, 방탄, 지진, 온도유지 등 다양한 건물 고려사항, Battery banks계산법, EMF 이슈를 피하기위한 최소거리 및 배치, 쿨링 셋업, CFM, Delta-T와 같은 요소들을 이해하는 등 데이터센터 구성 시 고려사항, 이슈사항 등을 이해하고 해결할 수 있습니다.
* 3일 과정 + 1일 시험으로 진행합니다. CDCS 자격증시험 일정은 교육 등록 후 별도 안내드립니다. * 한글 시험지를 제공하지 않습니다(Only English Exam) 참고 하시기 바랍니다. * 자격증 유효기간은 취득후 3년입니다. [학습목표] 데이터센터의 디자인 라이프 사이클을 이해한다. - 고객의 요구사항을 충족시키기 위해 벤더와 서블라이어에 따른 디테일한 요구사항을 확인한다.
- 벤더로부터 제안된 기술적인 디자인 플랜, 견적, 제안을 검증할수 있다.
- Maintenance Tier-level과 데이터센터 디자인을 위한 Tier-level을 이해한다.
- 소방대책, 방탄, 지진, 온도유지 등 다양한 건물 고려사항을 이해한다.
- 고객 요구사항을 충족시키기위해 어떻게 Battery banks를 계산하는지 이해한다.
- 장비간 간섭에 대한 영향을 줄이고 작업자 안전을 위해 EMF 이슈를 피하기위한 최소거리 및 배치를 애해한다.
- 쿨링 셋업, CFM, Delta-T와 같은 요소들을 이해한다.
- 데이터센터에 적합한 UPS와 UPS병행구성에 대해 이해하고 UPS병행구성시 발생하는 전반적인 고려사항들을 살펴본다
- Single Line Electrical Diagram을 읽는 방법을 이해하고 가장 보편적으로 발생하는 디자인 이슈를 확인한다.
|
교육내용 |
Data Centre Design / Life Cycle Overview Overview of the phases of a data centre life cycle Planning, re-alignment and continuous improvement Tier Levels History of ‘tier level’ definitions Tier level definitions, categories and measure points Redundancy options Tiered Infrastructure Maintenance Standards (TIMS) Building Considerations & Standards Floor loading requirements Fire rating for walls and glass Blast protection Bullet proofing Forced entry protection Advanced Raised Floor & Suspended Ceiling Raised floor installation guidelines to ensure contractors install a proper closed and levelled raised access floor Choosing the right tiles and their locations Seismic mitigating floor constructions Choosing the correct suspended ceiling Advanced Power Power infrastructure layout; Formulas which you should know for the data centre Single Line Electrical diagrams; how to read to ensure key components are present for protection Over current protection devices (MCB/MCCB/VCB/ACB/Fuses) definitions and what to use where Earth Leakage devices (RCB/RCD/ELCB/GFCI/ALCI/RCBO), definitions and what to use where Lightning strikes and surge protection devices (TVSS/ SPD), how they operate, where to use and how to install Power cabling and cable run considerations PDU/DB setup and minimum requirements Generators; Component make up Choosing the required device Calculate required fuel storage tank capacity Paralleling of gen-sets Regulatory requirements UPS Systems; Required specifications for UPS systems How to read data sheets and select the correct UPS Requirements for parallel configurations and avoid pitfalls such as single point of failures How parallel installation should be done, classic mistakes made by installers and how to avoid these Harmonic Filters; Type of ?filters available and which one to select depending on the application Battery Banks; Designing battery banks, how to calculate, and double check the battery bank to be installed Battery charging pitfalls and ensuring the right charger is being installed and used Using parallel battery banks; how to properly install them, limitations and risk when using batteries in parallel How to test batteries correctly and make decisions on cell/block or string replacement Battery casing choices; ABS, V0, V1, V2 Alternative energy storage; flywheel, re-useable cell etc. Advanced Electro Magnetic Fields Differences between single, three phase and bus-bar EMF Options available to measure EMF and how to interpret the results from single axe and composite measurements Guidance on safe distance for equipment and humans Calculation of EMF attenuation factor for shielding material permeability and saturation factors Advanced Cooling Environmental class definitions and thermal specifications Equipment airflow and Delta-T definitions and limits Planning for floor, rack and cooling equipment CFM requirement calculations and conversions Air-conditioner specifications and how to select the correct air-conditioner with the required capacity and flow Techniques for optimization of airflow Redundancy guidelines for air-conditioners avoiding classic misconceptions Liquid cooling guidelines for data centres Advanced Fire Protection Fire triangle and elements to stop a ?re Detection systems in detail (VESDA, VIEW, Smoke sensors) Considerations for installation of sensors Difference in water based systems i.e. dry-pipe, pre-action and why most of them don't work and how to detect this Details on Inert, Halocarbon, fluorinated systems and how to select the correct gas for your data centre How to calculate the gas content ensuring the appropriate level is installed to suppress the ?re Other requirements for gas systems (release times, hold times, pipe install requirements and other important factors Requirements for the ?re panel Installation verification, what to check and how New ?re suppression techniques which prevents ?res from Igniting Cable Management In rack power and network cabling Labelling based on TIA-606 Environmental Specifications Acoustic noise regulations, specifications, effects and limits Data centre contaminations and classifications Measurements, standards and limits Preventive measures and avoidance Electro Static Discharge (ESD) Data Centre Efficiency Power efficiency indicators How to measure it and what are acceptable numbers compared to the general industry How to achieve power savings in the data centre; various techniques to save energy in all parts of the data centre i.e. application/system level, cooling, power distribution Mock Exam EXAM: Certified Data Centre Specialist
|